Milltronics CVCC Instrukcja Obsługi Strona 16
- Strona / 112
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
INSTALLING THE TRANSDUCER
INSTALLING THE TEMPERATURE SENSOR
Max cable run 183 m (600 ft) of
RG-62U or equivalent. Cable must
be run in a grounded metal conduit
with no other cabling (except
Temp. Sensor cable).
Ground shield at OCM-3 only.
Insulate shield at junctions to
prevent inadvertent grounding.
Basic Wiring – Temperature Sensor
Basic Wiring – Transducer
Maximum cable run 183 m (600 ft) of
Beldon 8760, 1 pair shielded/twisted,
18 AWG or equivalent.
Temperature sensor cable can be
run with the transducer cable in a
grounded metal conduit.
Ground shield at OCM-3 only.
In order to compensate for uniform
temperature change in the air
between the transducer and the flow
surface, the temperature sensor
must be connected to the OCM-3.
Hazardous voltage present on transducer terminals during operation.
Note: When using the XRS-5 transducer with the OCM-3, use the TS-2 external
temperature sensor. The internal temperature sensor in the XRS-5 cannot be used.
16 OCM III 7ML19985AB01
- Measurement 2
- Continuous 2
- Weighing Systems 2
- TABLE OF CONTENTS 3
- 7ML19985AB01 OCM III 6 6
- ABOUT THIS 7
- SPECIFICATIONS 9
- PROGRAMMER 10
- TRANSDUCER 11
- TEMPERATURE SENSOR 11
- COMMUNICATION SOFTWARE 12
- INSTALLATION 13
- OCM-3 LAYOUT 14
- SYSTEM DIAGRAM 15
- INSTALLING THE TRANSDUCER 16
- 17 OCM III 7ML19985AB01 17
- SYNCHRONIZATION 18
- POWER CONNECTIONS 19
- DC POWER 19
- AC POWER 19
- COMMUNICATING VIA COMPUTER 20
- INSTALLING THE PROGRAMMER 20
- START UP 21
- INITIAL START UP 22
- 11: 41 a.m 24
- FUNDAMENTAL CHECKS 25
- 7ML19985AB01 OCM III 26 26
- OPERATION 27
- FLOW CALCULATION 28
- FAIL-SAFE 31
- FLOW RATE AND TOTALIZING 31
- Flow rate 31
- Viewing the data log 33
- 7ML19985AB01 OCM III 33 33
- BLANKING 34
- TEMPERATURE 34
- TIME AND DATE 34
- EMULATION MODE 35
- FLOW VELOCITY INPUT 36
- AUXILIARY HEAD INPUT 36
- DC OUTPUT 37
- DIAGNOSTIC AIDS 37
- ‘D’ PARAMETER LISTING 38
- 7ML19985AB01 OCM III 40 39
- ‘F’ PARAMETER LISTING 40
- 7ML19985AB01 OCM III 42 41
- ‘P’ PARAMETER LISTING 42
- flowrate 43
- % flow / min 48
- ‘U’ parameters required * 52
- U1 = throat width b U5 = Cd 57
- U2 = hump height p U6 = A 57
- U3 = throat length L 57
- BS-3680 RECTANGULAR FLUME 58
- blanking value, P47 58
- 7ML19985AB01 OCM III 59 58
- U0 = crest width b U3 = Cv 59
- U1 = crest height p U4 = Cd 59
- U2 = crest length L U5 = A 59
- 7ML19985AB01 OCM III 61 60
- U1 = throat width b U6 = Cd 61
- U2 = hump height p U7 = Cs 61
- U3 = throat length L U8 = A 61
- U4 = slope m 61
- BS-3680 TRAPEZOIDAL FLUME 62
- 7ML19985AB01 OCM III 63 62
- BS-3680 U-Flume, P3 = 4 63
- BS-3680 U-FLUME 64
- 7ML19985AB01 OCM III 65 64
- U0 = crest width b U3 = C 65
- U1 = crest height p U4 = Cp 65
- U2 = crest length L 65
- BS-3680 FINITE CREST WEIR 66
- 3 to 4 x h 66
- 7ML19985AB01 OCM III 67 66
- U1 = crest width b U4 = K 67
- U2 = crest height p 67
- 7ML19985AB01 OCM III 69 68
- Reference 69
- 7ML19985AB01 OCM III 71 70
- RECTANGULAR WEIR - CONTRACTED 72
- 7ML19985AB01 OCM III 73 72
- ‘U’ parameters required ** 75
- PALMER-BOWLUS FLUME 76
- blanking value, P47 76
- 7ML19985AB01 OCM III 77 76
- RECTANGULAR AREA X VELOCITY 82
- 7ML19985AB01 OCM III 83 82
- U1 = channel base width b 83
- U2 = channel depth ht 83
- TRAPEZOIDAL AREA X VELOCITY 84
- 7ML19985AB01 OCM III 85 84
- U1 = channel base width b 85
- U2 = transition height ht 85
- 7ML19985AB01 OCM III 87 86
- 7ML19985AB01 OCM III 88 87
- U-CHANNEL AREA x VELOCITY 88
- 7ML19985AB01 OCM III 89 88
- 7ML19985AB01 OCM III 90 89
- U1 = lower angle alpha (α) 91
- U2 = upper angle beta (β) 91
- U3 = transition height ht 91
- GULL WING AREA X VELOCITY 92
- 7ML19985AB01 OCM III 93 92
- U1 = bottom radius r 93
- U2 = axial displacement d 93
- 7ML19985AB01 OCM III 98 97
- MAINTENANCE 98
- ERROR CODES 99
- COMMUNICATIONS 100
- Protocol 101
- Interconnection 102
- Timed Print Out 103
- Command Response 107
- Modem Communication 109
- Establishing Communication 110
- Ending Communication 111
- *7ml19985AB01* 112
- Rev. 1.0 112
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Milltronics CVCC
(76 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji